Schematic Reference

Audio Stereo Channel Selector Circuit

This circuit has accouterment for abutting stereo outputs from four altered sources/channels as inputs and alone one of them is selected/connected to the achievement at any one time.

When ability accumulation is angry ‘on’, approach A (AR and AL) is selected. If no audio is present in approach A, the ambit waits for some time and again selects the abutting approach (channel B). This chase operation continues until it detects audio arresting in one of the channels. The inter-channel adjournment or adjournment time can be adapted with the advice of preset VR1. If still best time is needed, one may alter capacitor C1 with a capacitor of college value.

Suppose approach A is affiliated to a band recorder and approach B is affiliated to a radio receiver. If initially approach A is selected, the audio from the band recorder will be present at the output. After the band is played completely, or if there is acceptable abeyance amid after recordings, the ambit automatically switches over to the achievement from the radio receiver. To manually skip over from one (selected) alive approach to addition (non-selected) alive channel, artlessly advance the skip about-face (S1) briefly already or more, until the adapted approach ascribe gets selected. The called approach (A, B, C, or D) is adumbrated by the aglow of agnate LED (LED11, LED12, LED13, or LED14 respectively).

IC CD4066 contains four alternation switches. These switches are affiliated to four abstracted channels. For stereo operation, two agnate CD4066 ICs are acclimated as apparent in the circuit. These alternation switches are controlled by IC CD4017 outputs. CD4017 is a 10-bit arena adverse IC. Since alone one of its outputs is aerial at any instant, alone one about-face will be bankrupt at a time. IC CD4017 is configured as a 4-bit arena adverse by abutting the fifth achievement Q4 (pin 10) to the displace pin. Capacitor C5 in affiliation with resistor R6 forms a power-on-reset ambit for IC2, so that on antecedent switching ‘on’ of the ability supply, achievement Q0 (pin 3) is consistently ‘high’. The alarm arresting to CD4017 is provided by IC1 (NE555) which acts as an astable multivibrator back transistor T1 is in cut- off state.

IC5 (KA2281) is acclimated actuality for not alone advertence the audio levels of the called stereo channel, but additionally for advanced biasing transistor T1. As anon as a specific beginning audio akin is detected in a called channel, pin 7 and/or pin 10 of IC5 goes ‘low’. This low akin is accompanying to the abject of transistor T1, through diode-resistor aggregate of D2-R1/D3-R22. As a result, transistor T1 conducts and causes achievement of IC1 to abide ‘low’ (disabled) as continued as the called approach achievement exceeds the preset audio beginning level.

Presets VR2 and VR3 accept been included for acclimation of alone audio beginning levels of larboard and appropriate stereo channels, as desired. Already the multivibrator activity of IC1 is disabled, achievement of IC2 does not change further. Hence, analytic through the channels continues until it receives an audio arresting beyond the preset beginning value. The skip about-face S1 is acclimated to skip a approach alike if audio is present in the called channel. The cardinal of channels can be calmly continued up to ten, by application added 4066 ICs.

6 Watt Audio Amplifier Schematic Circuit with TDA1519

The audio amplifier circuit is on the TDA1519 amplifier IC that is based in audio applications, which is not a aerial achievement ability can be used. The ambit TDA1519 is a ability of 2×6 watts.

The TDA1519 is an amplifier congenital Class B dual-output advance in a 9-by-line (SIL) artificial amalgamation boilerplate achievement is primarily developed for car radio applications.

Key Features of the audio amplifier IC TDA1519 are: Requires few alien components, anchored gain, acceptable bounce drive, aphasiac / standby mode, thermal protection, about-face polarity safe. Tda1519 amplifier ability rating, 14.4 volts.

This amplifier circuit based on the ic, and the use here is that where ic STK4017 IC has output power of 6.5 watts with the impedance 8Ohm. Minimum required supply voltage and maximum 20Volt 35 Volt DC.

• P1_____________10K Log.Potentiometer
• R1,R2__________33K 1/4W Resistors
• R3_____________33R 1/4W Resistor
• R4_____________15K 1/4W Resistor
• R5,R6___________1K 1/4W Resistors
• R7____________680R 1/4W Resistor
• R8____________120R 1/2W Resistor
• R9____________100R 1/2W Trimmer Cermet
• C1,C2__________10µF 63V Electrolytic Capacitors
• C3____________100µF 25V Electrolytic Capacitor
• C4,C7_________470µF 25V Electrolytic Capacitors
• C5_____________47pF 63V Ceramic Capacitor
• C6____________220nF 63V Polyester Capacitor
• C8___________1000µF 25V Electrolytic Capacitor
• D1___________1N4148 75V 150mA Diode
• Q1____________BC560C 45V 100mA PNP Low noise High gain Transistor
• Q2____________BC337 45V 800mA NPN Transistor
• Q3____________TIP31A 60V 4A NPN Transistor
• Q4 ___________TIP32A 60V 4A PNP Transistor
• SW1___________SPST switch

•     Resistor R1 : 1k2
•     Resistor variable R2 : 10k
•     IC : LM3915
•     LED indicator LED1-LED10 : LED 5mm
•     12V power supply

•     Resistor R1:  47k ohm
•     Resistor R2 : 22k ohm
•     Resistor R3 : 220 ohm
•     Diode D1-D7 : 1N4001
•     VR1 : 1k ohm
•     Polar capacitor C1 : 470 uF/25V
•     Polar capacitor C2 : 1 uF
•     Capacitor C3 : 0.1 uF
•     Transistor T1-T2 : BC148
•     Transformer X1 : 220 V AC/0-12V AC
•     X2 : AF output
•     Transistor SCR1-SCR2 : BA654